Manley Mastering Version Slam
First, read about the Manley SLAM! Regular Version. This page mostly covers what is different about the Regular and Mastering Versions, not the basic features that both versions have.
First off: no microphone preamps. You mastering engineers certainly don't need those.
The mic pre and input select switch are removed and the switches become dedicated "mode" switches one each for the ELOP® and the FET limiters.
1) The ELOP® limiter gets more Ratios - 10:1, 5:1, 3:1, 2:1 and something new called AutoHF which starts off as a 1.5:1 ratio and increases gradually to 10:1 for highs. This is something like a de-esser, and of course can work with the ELOP SC toggle at 200Hz for even more effect.
2) The FET limiters get new modes that are 50%, NORM, LP Lim, BOTH, and CLIP.
The "50%" setting mixes in the straight signal to the limited signal which is often difficult to do in a mastering environment and because the FET sidechain 'reads' off the output, the amount of gain reduction doubles. It resembles halving the FET ratio but is cleaner due to the mix.
The "LP Lim" setting only comes into play for hot signals and reduces the depth of gain reduction for high freqs. This translates to - hot signals + moderate gain reduction = brighter, more present signal, less distortion, more balls. This mode allows more high frequencies to pass through without being limited.
The "CLIP" setting introduces a fixed threshold clipper circuit set up about -2 dB DFS or +18 dBv at the XLR. Within normal usage "CLIP" generally prevents outputs from passing beyond +18 dBv, and 97% of the time, clips in a controlled fast-recovery manner before a converter would (in generally a less than desirable sounding way).
Finally, the "BOTH" setting on the FET limiter engages both the "LP Limit" and the "CLIP" functions at the same time. This might be appropriate for metal and projects demanding intense volume. The "BOTH" mode is designed for situations where extreme processing and loudness is required but where attack, brightness and aggressiveness needs to be preserved or enhanced.
3) The LEFT blue erstwhile-"limit" button becomes a master stereo LIMIT bypass switch here in the Mastering Version. When it is not engaged, it becomes a true hard-wire bypass (This was not possible on the mic preamp regular version obviously).
4) The Right blue button becomes the DAC select switch (stereo).
5) The what-was-the-Phantom toggle on the back of the unit becomes the Unbalanced 1/4" jack input select in this new mastering version.
6) No pots. All knobs in the Mastering Version are detented in mostly 1 dB steps, with some appropriate 1/2 dB and 2 dB steps, right where they should be.
MORE INFO ABOUT SLAM! MASTERING VERSION (from the Owner's Manual Addendum)
The mastering version has a number of changes compared to the regular SLAM!
There are no mic preamps or instrument inputs. Instead the tube sections are paralleled for lower noise and distortion.
All pots are replaced with rotary switches for detented resettability and easier cal.
The mastering version has a true hard-wire bypass function, which is not possible on the regular version with mic preamps, etc. What was the Left Bypass, becomes the full Bypass (in stereo and hardwired). No separate L & R bypass buttons.
The right BYPASS button becomes either the DAC select if the Digital Converter Option is installed - or - Limiter Bypass (tubes & transformers still active)
There are dedicated unbalanced transformerless inputs on the mastering version. What was the Phantom Power switch on the back now selects XLR or 1/4" inputs.
The ELOP® limiter now has 5 ratios, which may put it into the compressor/ limiter category. The lower ratios may be better suited for complex mixes.
The FET limiter has 5 modes (these last two features replace the INPUT selector).
We calibrate/build the digital option for +14dBu =DFS rather than +16 dBu.
About item 6, the ELOP® can be selected for 10:1, 5:1, 3:1, 2:1 and a new 'AUTO HF' mode where high frequencies get a higher ratio and low freqs get a low ratio. This mode is the most gentle. As with most compressors one might need to lower the threshold as one lowers the ratio, if keeping a similar depth of gain reduction is wanted. The threshold markings are based on the 10:1 ratio and a setting of +18 is intended to help reduce DFS overs with a converter with 14 dB of headroom over +4 dBm. Many mastering converters are set for 14 dB of headroom and the +18 setting would be a good starting point. Of course being an Opto-based limiter, it cannot be ultra-fast and some peaks will probably get through and it generally will have the typical (puffy) sound of an opto (because of its inherent time constants). It should be pointed out that much of that character is reduced when used in conjunction with the FET limiter. The FET usually catches some of the overshoots and time/gain behavior of the Vactrol and that can reduce the familiar Optical sonic signature.
The FET limiter has some subtle enhancements, some of which will not be apparent on all sessions. In particular, the LP LIM function will not be obvious unless the input signals are rather hot and more than a few dB of limiting is taking place. LP LIM is meant for those jobs that require more drastic treatments. If those conditions are met, 1) the NORM setting may be verging on 'crunchy' and might seem dulled due to reduced transients, 2) the LP LIM setting can be less crunchy, and seem to have more 'presence' because the FET limiter won't be pulling down as much mids and highs as it will lows where most of the energy is. It may also be difficult to compare NORM and LP LIM because the change involves a 3 or 4 second time constant. At normal levels, the two modes will be similar sounding. LP LIM seems to help in extreme cases where loudness is the prime goal. Use the Bypass button to check how much dynamic presence is added.
The 50% setting mixes some raw input with the post limiter signal, which is often difficult in a mastering environment. Because the FET side-chain senses right off the output XLR, one immediate indication is significantly deeper gain reduction shown on the LED ladder, but less apparent limiting to our ears. In some ways, it is like reducing the ratio and threshold, maintaining a similar output level. It may sound a bit more open and may be useful where lower level passages need to be raised without killing all transients. Another benefit is that the raw parallel path flows through less circuitry.
The CLIP setting just introduces a soft clip circuit just below +18 dBv or about a dB shy of where a converter set for +14 of headroom might hit DFS clipping. This could allow one more safety valve with a bit of room for the digital filters to behave nicely. One may follow that process with a digital limiter to lift the level a bit closer to DFS if desired.
You may notice that the ATTACK switch simulates some of the audible action we associate with attack controls on compressors but still tends to grab most of the fast peaks. In other words, you get some punch with slower attacks. Like other attack controls you may have to adjust the threshold down at slower settings to maintain some clip protection, but may notice that you don't have to adjust the threshold as much as one might expect with a conventional attack control. This is because there is a very fast limiter still hitting transients that are near our threshold of identifying.
Should also point out that the ELOP® side-chain filter has some level compensation built in so that chopping off the lows, doesn't cause a huge change in thresholds. There may be some adjustment required depending on the spectral balance of the music though. With bright mixes the 200 Hz may actually cause deeper limiting, plus there is a 3 dB peak above 4K to help smooth excessive sibilance, though we don't refer to it as a de-esser.
The hard-wire bypass function is not quite as trivial as might be expected. It is a bit more complicated because of 2 input jacks, plus the DAC option and the 2 different outputs, one of which doubles as an input to the A to D option, plus all the metering. Selection of either the XLR balanced (transformer) input or 1/4" unbalanced (op-amp) is done with a "pull to toggle" switch on the back panel. Generally either output can be used and there are internal jumpers that allow the XLR output to be used as an input to the A/D, FET side-chain and OP metering, so that the SLAM! can be used in a wild way with other processors (like a Massive Passive) in a complex chain. Like many of Manley's processors, using the 1/4" unbalanced output bypasses the final transformer and may be a little cleaner or open sounding compared to the transformer output, which may be a little warmer and richer or evocative of some vintage gear. Might be worth checking out each input and output while you learn the unit. Subtle but important differences.
If the converter option is installed, and DAC is selected, it will still be available in bypass. The XLR output will be the same as the dedicated 1/4" DAC output then. The first few units do not pass the DAC to the 1/4" in Bypass (only). It should also be noted that in balanced mode the DAC produces +4 dBm or 0VU @ -14 DFS to the SLAM! circuitry, but in unbalanced mode produces -2 dBm or -6VU @ -14 DFS. This difference might be a flaw or feature, but with the SLAM! being a level changing device, it should not be a problem. The dedicated 1/4" balanced DAC output is -14 DFS = +4 or 0VU. There are a pair of internal trims on the DAC amplifier if a different 'standard' than -14 DFS = 0VU or the consumer DFS = 2 volts RMS unbalanced is desired.
A few points inspired by some of the early comments from SLAM! users, make it into this addendum too.
The SLAM!® is designed primarily as an old school text book limiter and as such the Output Level knob is not after the final FET limiter. The idea is to set the peak-stop threshold and adjust the incoming level, which is why the level controls are larger. More fun is to be had adjusting the Input and Output Level controls than the Thresholds, which can often just be thought of as 'set and forget' especially if the FET Attack time tends to live in one setting. The Output level is not a 'gain make-up' control typical of a compressor but consider it as another Input level before the FET and after the ELOP®.
Some of the skills or habits we have with soft compressors, might be less useful with a limiter. For example, just setting it by ear, with similar input / output levels and an acceptable number of dBs of gain reduction or approaching it as an effect might not get the best results. The approach of trying to achieve a brick wall level and then tweaking how the unit is driven (those Input and Output knobs) usually seems to work best. Put another way, limiters or limiting is not often a great effect in itself, but the increased volume when it is used reasonably can be. So it is about loudness rather than a cool pumping action, or pleasant warmth. It can do some of that, but was designed to be pretty clean for a tubed unit, and hot aggressive colors can be dialed in with the FET limiter.
The LED Gain reduction display is 1 dB per segment. We have seen numerous people at trade shows dial up 15-30 dB of gain reduction presumably to see a good number of LEDs flashing. It is still a limiter and should be treated with some respect of the damage a powerful limiter in the wrong hands can do. In other words, it can be particularly vicious. The worst-case scenario is bass-heavy mixes, fast attack and releases, and deep limiting, where some GR modulation can happen. Though much has been done to allow those very fast releases, which maximize loudness, it does pay to be aware that distortions and edginess might be a side effect. Sometimes the best answer is exactly what many mastering engineers do daily, which is use 2 or 3 compressor/limiters each doing a few dB rather than one doing 10 dB. The LED meters can be very useful in comparing peak levels, especially when used with the Bypass button. Part of the secret to getting the most out of the SLAM!, is to learn the LED meter modes. Everybody has a favorite display mode, but they all are rather useful and you may find yourself changing modes more than expected. Of course, some rely too much on the meters and forget to listen and assume that particular operating levels are important. There is a healthy range of signal levels that are easily accommodated. We only suggest using less limiting for the first few weeks until you are reasonably familiar with the unit. There is a learning curve and no real tricks or settings that seem to be common. Every mix may be different.
Lastly, it is not in any way like the Variable Mu® and was never intended to be. Each has its own purpose and special 'unique talent'. The SLAM! may be easier to describe as a damn-fast transient killing secret weapon, or a tubed, analog L-2 with amazing converters, or maybe just a serious "go-louder box" with huge cajones. Enjoy!
Features & Specifications
Vacuum tubes: 2 x 12AT7WA, 2 x 6414 dual triodes
MANLEY transformer coupled Balanced Inputs and Outputs
Gain: 20dB max Limiter Gain
FET Attack approx. 100uS; Release 10mS to 2Sec; Ratio: better than 20:1
ELOP Attack approx. 10mS for 6dB GR; Release 2.5 Sec; Ratio: 10:1
AES 24Bit 192KHz upsampling from 44.1, 48, 88.2, & 96KHz
A to D 24Bit 96KHz (for now)
Frequency Response: 5Hz to 60KHz
Maximum Output : +32dBm, +30dBm (into 1KΩ load)
THD+N <.05% @ 1KHz Dynamic Range: 115dB typical
Output Impedance: 200Ω
Power Consumption (120/240 VAC): less than 100 watts
Size 19" X 12" X 3.5" (occupies 2u)
Shipping Weight: 25 lbs.
See also: SLAM! Regular Version
BASE UNIT ANALOG SLAM!: $6,600.00 more info
Digital I/O Interface option factory-installed: $2,500.00
MASTERING VERSION SLAM! $7,600 USD
Please call Dave at (510) 581-3817 for product information and your price.